CPU H226IL 220VAC
128 KB de memoria de programa + 128 KB para librerías de funciones, 64 KB de memoria de datos + 100 KB de memoria de datos permanente, alimentación 220 VAC, 24DI / 16DO relé 2 A, 2 puertos PPI / FPORT, 1 puerto Ethernet. Almacenamiento de datos permanentemente. Soporte control analógico, tarjetas de expansión CAN y RS485, compatible con protocolo S7.
Performance Parameters
| Physical Features | |||||||||||||||
| Dimension（W×H×D） | 196.5×80×62mm | ||||||||||||||
| Power consumption | 11W | ||||||||||||||
| Program memory | 128K+64K+64K | ||||||||||||||
| Data memory | 64KB+100KB，Data permanent stored | ||||||||||||||
| Maximum number of expansion modules | 7 | ||||||||||||||
| Maximum digital | 128DI/128DO（expand CAN expansion board up to 640DI/640DO） | ||||||||||||||
| Maximum analog | 32AI/32AQ（expand CAN expansion board up to 194AI/194AO） | ||||||||||||||
| Data stored | FlashROM Data permanent stored | ||||||||||||||
| Power supply features | |||||||||||||||
| Rated input voltage | AC220V | ||||||||||||||
| Impulse current | 264VAC,20A | ||||||||||||||
| Isolation (field and logic) | 1500VAC | ||||||||||||||
| Hold time (power off) | 20ms/80ms above，120/240VAC | ||||||||||||||
| Sensor +24V power output | Voltage range：20.4~28.8VDC | ||||||||||||||
| Rated current：300mA | |||||||||||||||
| Maximum ripple noise (<10MHz) ：<1V peak-to-peak value | |||||||||||||||
| Isolation (sensor and logic)：None | |||||||||||||||
| Power alarm | when it is lower than 15V, the alarm bit SM195.1 | ||||||||||||||
| Regular features | |||||||||||||||
| Total timers | 512 | ||||||||||||||
| 1ms | 4 | ||||||||||||||
| 10ms | 272 | ||||||||||||||
| 100ms | 236 | ||||||||||||||
| Counters | 256 | ||||||||||||||
| Accumulators | 4 | ||||||||||||||
| Memory bit | 256bit | ||||||||||||||
| Local storage（L） | 64 bytes independent | ||||||||||||||
| Sequence control relay（S) | 256 bit | ||||||||||||||
| Time interrupt | 2*1ms resolutions | ||||||||||||||
| Edge breaks | 8 | ||||||||||||||
| Boolean operation execution time | ≤0.15us | ||||||||||||||
| Floating operation execution time | ≤6.2us | ||||||||||||||
| Real time clock | Built-in | ||||||||||||||
| BD expansion board port | One ,BD expansion board supports RS485 expansion board, CAN expansion board, and analog expansion board | ||||||||||||||
| System indicator | SF indicator （red） | ON：Program error，OFF：Normal | |||||||||||||
| DIAG indicator （orange） | ON：Program control,OFF：Normal | ||||||||||||||
| RUN indicator （green） | ON：running，OFF：stopped | ||||||||||||||
| STOP indicator （orange） | ON：stopped，OFF：running | ||||||||||||||
| RMC indicator （green） | ON：remote control is connected，OFF：remote control is disconnected | ||||||||||||||
| LNK/ACT indicator （green） | ON：Ethernet connection，Blinking: Transmission is underway，OFF：disconnect | ||||||||||||||
| Run switch | RUN/STOP | ||||||||||||||
| External battery port | 1、Special battery card;2. Professional battery holder (CR1220) supports either external battery | ||||||||||||||
| Programming card | Support | ||||||||||||||
| Integrated communication capabilities (PPI/ free port) | |||||||||||||||
| Communication interface | 2 Communication port： PORT0:PPI/free port，standard RS485 PORT1:PPI/free port，standard RS485 After the RS485 expansion board is plugged in and restarted, PORT0 (RS485, PPI communication port) PORT1 (RS485, PPI/ free port), FPORT0 (free port) |
||||||||||||||
| Baud rate(baud) | 9.6k、19.2k and 187.5k | ||||||||||||||
| Free port baud rate(baud) | 1.2k ~ 115.2k | ||||||||||||||
| Maximum number of stations | 32 stations per segment, 126 stations per network | ||||||||||||||
| Maximum number of main stations | 32 | ||||||||||||||
| Point-to-point (PPI master mode) | Yes(NETR/NETW)，With a maximum of 8 connections and a maximum communication of 200 bytes per connection | ||||||||||||||
| MPI connect | 8（1PG/1OP），2 reserved | ||||||||||||||
| Maximum cable length per section
Use an isolated repeater No isolated repeater is used |
The baud rate is 1000 m at 187.5 K and 1200 m at 38.4 K
50m |
||||||||||||||
| Ethernet Communication | |||||||||||||||
| Communication port | 1 Standard Ethernet port | ||||||||||||||
| Communication standards | IEEE802.3 standards | ||||||||||||||
| Transmission speed | 10Mbps/100Mbps adaptive | ||||||||||||||
| Adaptive cross-connect | Support | ||||||||||||||
| Hardware interface | RJ45 | ||||||||||||||
| Protocol Type | UDP/TCP protocol
Supports UDP_PPI, MODBUS_TCP, Socket, and S7 protocols, Ethernet communication between PLCS, and MiCo Ethernet programming. |
||||||||||||||
| Configuration mode | Ethernet port search PLC,support the mouth download system configuration. | ||||||||||||||
| Maximum number of connections | 8 UDP/PPI connections, no master or slave | ||||||||||||||
| 8 TCP/Modbus connections, no master or slave | |||||||||||||||
| 4 Socket connections, 2 UDP, 2 TCP | |||||||||||||||
| 8 S7 protocol, no master and slave, COTRUST PLC only as slave station | |||||||||||||||
| Maximum single data transmission | Up to 200 bytes for UDP_PPI transmission. | ||||||||||||||
| Up to 240 bytes are used for ModBus_TCP transmission. | |||||||||||||||
| Up to 512 bytes is used for Socket transmission | |||||||||||||||
| Up to 200 bytes for S7 transmission | |||||||||||||||
| Startup time of network port | 5 to 10 seconds. The startup time varies depending on the network environment. | ||||||||||||||
| Indicator | RMC | On: The remote server is successfully connected | |||||||||||||
| Off: The remote connection is disconnected or the remote function is disabled | |||||||||||||||
| LINK/ACT | On: The hardware of the network port is connected | ||||||||||||||
| Blinking: Data is being exchanged | |||||||||||||||
| Off: The hardware of the network port is disconnected | |||||||||||||||
| The length of the communication cable | 100M，cable type is CAT5e or above | ||||||||||||||
| Isolation | Communication isolation | ||||||||||||||
| IP address reset function | Five consecutive times within two seconds | ||||||||||||||
| Upgrade Firmware function | Use MagicWorks PLC and MiCo to remotely upgrade firmware from company servers over Ethernet | ||||||||||||||
| I/O Features | |||||||||||||||
| Number of integrated digital inputs | 24 | ||||||||||||||
| Input type | Leak/Source | ||||||||||||||
| Number of integrated digital outputs | 16 | ||||||||||||||
| Output type | Source | ||||||||||||||
| Maximum digital | 128DI/128DO（expand CAN expansion board up to 640DI/640DO) | ||||||||||||||
| Maximum analog | 32AI/32AQ（expand CAN expansion board up to 194AI/194AQ） | ||||||||||||||
| The maximum number of local expansion IO modules | 7 | ||||||||||||||
| Pulse capture input | 14 | ||||||||||||||
| High-speed counters | Total Uniphase countersAB-phase counters |
6 6×50KHz 4×30KHz |
|||||||||||||
| Integrated Communication Function (CANopen) – use for CAN communication board model CTH2-CAN-01S2-EB | |||||||||||||||
| Communication Interface | 1（8 Pin） | ||||||||||||||
| Communication speed（kbps） | 1000 | 800 | 500 | 250 | 150 | 50 | 20 | ||||||||
| Maximum cable length（m） | 25 | 50 | 100 | 250 | 500 | 1000 | 2500 | ||||||||
| Maximum station address | 127 | ||||||||||||||
| Station address range | 1-127 | ||||||||||||||
| Maximum number of master and slave stations | 32 | ||||||||||||||
| Configuration method | CAN configuration blocks and EDS files | ||||||||||||||
| Maximum digital access | Nomal IO | CANopen IO | |||||||||||||
| Byte | Memory starting address | Byte | Memory starting address | ||||||||||||
| Input | 16 | IB0 | Input | 64 | IB16 | ||||||||||
| Output | 16 | QB0 | Output | 64 | QB16 | ||||||||||
| Maximum analog access | Normal IO | CANopen IO | |||||||||||||
| Channel | Memory starting address | Channel | Memory starting address | ||||||||||||
| Input | 32 | AIW0 | Input | 162 | AIW64 | ||||||||||
| Output | 32 | AQW0 | Output | 162 | AQW64 | ||||||||||
| Integrated Communication Function (CANFree) – Used when extending the CAN communication board | |||||||||||||||
| Communication Protocol | CanFree | ||||||||||||||
| Use method | Supported by internal library instructions | ||||||||||||||
| Digital input features | |||||||||||||||
| Number of interated digital input | 24 | ||||||||||||||
| Input type | Leak/source | ||||||||||||||
| Rated voltage | 24 VDC | ||||||||||||||
| Maximum continuous allowable voltage | 30 VDC | ||||||||||||||
| Logic 1 signal (min.) | 18 VDC，3.0mA | ||||||||||||||
| Logical 0 signal (Max.) | 5 VDC，1mA | ||||||||||||||
| Isolation (field and logic)
Isolation group |
500 VAC，1min | ||||||||||||||
| Simultaneously connected input | 24 | ||||||||||||||
| Maximum cable length | 500m | ||||||||||||||
| Shielding: 50 m (high speed counter input); Unshielded: 300 meters (standard input) | |||||||||||||||
| Digital Output Features | |||||||||||||||
| Number of integrated digital output | 16 | ||||||||||||||
| Output type | Relays, dry contacts | ||||||||||||||
| Output frequency (maximum) | 100KHz（Q0.0-Q0.2），1KHz（Q0.3-Q1.7） | ||||||||||||||
| Rated voltage output | 24VDC,or 110V/220VAC | ||||||||||||||
| Output voltage range | 5-30VDC or 5-250VAC | ||||||||||||||
| Rated current per point | 2A | ||||||||||||||
| Rated current for each common point | 8A | ||||||||||||||
| Surge current | 7A，100ms | ||||||||||||||
| Lamp load (maximum) | 30W DC/200W AC | ||||||||||||||
| On resistance (contact) | 0.2Ω | ||||||||||||||
| Contact life (rated load) | 100,000 times on and off | ||||||||||||||
| Output of simultaneously connected | 10 | ||||||||||||||
| Parallel output | None | ||||||||||||||
| Maximum cable length | Shielde | 500m | |||||||||||||
| Unshielded | 150m | ||||||||||||||
También te puede interesar…
